In this article

Wash a wooden cutting board by hand with hot, soapy water after each use, rinse it, towel it dry and let it finish drying standing on edge. Never soak it or put it in the dishwasher. Oil it with food-grade mineral oil or the maker's board oil when it looks dry; one major board maker says at least once a month, depending on use. Use a separate board for raw meat, poultry and seafood.

Start with how you use the board

Decide which board you will use for ready-to-eat foods and which for raw meat, poultry, or seafood. Make the distinction easy to recognize in your own kitchen. A note inside the cabinet or an established storage position can help everyone follow the same routine.

U.S. food-safety guidance recommends separate boards for produce and raw animal foods, and hot, soapy washing for utensils and surfaces that contact raw ingredients. These are contamination-control steps, not a claim that one decorative wood species is automatically hygienic. Read the U.S. government food-safety steps.

Before a big meal, clear a spot where a washed board can dry. A routine only works if you can do it on a busy night.

How should you wash it after use?

Remove food debris, then follow the board maker's washing directions. Clean the working surface, edges, and any juice groove. Do not leave residue in a corner because the main face looks clean. Rinse away soap and move the board to the drying step rather than leaving it in the sink.

The USDA's cutting-board guidance says to wash boards with hot, soapy water between food tasks and replace them once excessive wear or grooves make cleaning difficult. This applies to the food-safety decision, independent of whether a board still looks attractive. See the USDA cutting-board guidance.

For ordinary wooden boards whose maker excludes soaking and dishwashing, keep them out of a sink of standing water and out of the dishwasher. These hard-maple board instructions give a product-specific example. If you cannot find your instructions, do not assume a quick machine cycle is approved. Directions for one board should not be extended to every bamboo, wood, or composite surface.

Is washing the same as sanitizing?

Washing removes food. If you also want to sanitize, use a method your board's maker allows. One major board maker's care FAQ gives 1 teaspoon of liquid chlorine bleach in 1 quart of water, or a 1-to-5 vinegar dilution, for its boards; rinse and dry afterward. Follow your sanitizer's label for contact time.

Never mix bleach with vinegar, ammonia or other cleaners. Lemon juice, a pleasant smell or fresh oil is not a sign that a board has been sanitized.

What does drying properly look like?

Towel away surface water with a clean cloth or paper towel, then allow the board to finish drying in a stable position with air around it. Make sure it cannot topple into the sink or slip onto the floor. Drying a board and storing a fully dry board are different stages.

One cutting-board maker recommends air drying on end and applying its approved mineral-oil-based care treatment to clean, dry wood. Its instructions are specific to its products and finish. Use the same distinction when reading your own maker's directions: washing first, drying next, maintenance afterward. See these cutting-board care questions.

Do not pack a still-damp board tightly between baking sheets or against another wet board. If it lives on the counter, check the contact area rather than judging dryness only from the exposed face. A good storage arrangement leaves the board easy to retrieve without turning the drying place into permanent clutter.

When should you oil the board?

Read the maker's instructions for the actual surface. An unfinished or oil-maintained cutting surface is not the same as a decorative, film-finished serving piece. Confirm that the item is intended for cutting before choosing a maintenance product.

Use an oil sold for cutting boards, such as food-grade mineral oil or the maker's board oil. Skip furniture polish, unlabeled workshop oils and cooking oils, which can turn sticky or rancid.

  1. Start with a clean board that has dried completely, ideally overnight.
  2. Pour a little oil on and spread an even coat over every surface, edges included.
  3. Let it soak in; several hours or overnight is common. Follow your oil's directions.
  4. Wipe off any oil that's still sitting on the surface.
  5. Repeat about monthly, or sooner if the wood looks pale and dry.

What about odors, stains, and roughness?

First repeat the appropriate washing and drying routine. Then describe what remains: an odor, discoloration, rough fibers, a groove, or an opening joint. They are different problems and should not all trigger sanding.

A maker may allow a particular deodorizing or resurfacing method on its solid-wood boards. That is not permission to use abrasives on a veneered serving tray or a board with an unknown finish. If the item is warped, cracked, separating, or difficult to clean, ask whether it should be replaced rather than trying to make it look new.

Make the routine work in a small kitchen

Keep a washing spot, a stable drying position, and a dry storage location available. They can be close together, but they do not have to be the same place. Put occasional serving pieces elsewhere so the daily board does not have to compete with them.

Before buying a larger board, picture lifting it to the sink, washing its edges, drying both faces, and returning it to storage. The board that fits the entire routine is more useful than one chosen only for the largest possible cutting surface.

Keep working through your next question

Find a practical dry-storage location.

Retire the board when

  • Knife grooves are deep enough to trap food
  • A joint has opened or a strip is loose
  • It's cracked through or badly warped
  • An odor or stain survives proper washing, drying and an approved odor treatment

Common questions

How often should you oil a wooden cutting board?

One major board maker recommends at least once a month, depending on how much you use it and how dry your home is. Oil sooner if the wood looks pale, dry or rough.

Can a wooden cutting board go in the dishwasher?

No. Board makers warn that dishwasher cycles and soaking disrupt the wood's moisture and can warp or split a board.

Can you use olive oil on a cutting board?

It's better not to. Cooking oils can turn sticky or rancid on wood. Use food-grade mineral oil or an oil sold for cutting boards.

Is wood or plastic safer for raw meat?

Either can be used if it's cleaned well and replaced when worn. What matters most is keeping a separate board for raw meat, poultry and seafood, and washing it with hot soapy water after use.